FAQs
A) Normally, we provide customer service with two hoses. If you want a stronger and more focused version, we can close one of the hoses with a rubber cap. This will double the amount of steam coming out of the remaining hose.
A) There are four temperature levels: 30°C, 40°C, 50°C, and 60°C. There are also four levels of mist control and two levels of wind control.
A) Steam helps open the cuticles on the scalp, allowing nutrition and treatments to penetrate the hair more effectively.
A) Attach the sucker of each hose to the inner side of the shampoo pottery, pointing towards the customer.
A) Check if the rubber gasket inside the water tank lid is wet. Remove any moisture and reassemble it.
A) Remove the steam head from the hose and cover it with the rubber cap. Then, cover the other hose with the steam cap.
A) After removing the water tank and funnel, wipe off any water stains on the walls and sides with a wet tissue.
A) Disconnect the hose that's connected to the holder and the main body. Extend the detached hose, add cleaner, shake it, and rinse thoroughly with water. Let it dry for about a day.
A) After removing the dust from the filter inside the filter case with water, dry the filter and reassemble it.
A) Open the drain hole and remove all the water from the device. Then, when you fill it with water again, the water level will be adjusted, and the steam will operate.
Step 1: Loosen the fastening bolt and connect it to the shampoo bowl.
Step 2: Wrap Teflon tape (to prevent water leakage) around the threaded area six times.
Step 3: Remove the white plug blocking the hose and check if there is a rubber gasket inside (if it's missing, please check the packaging box again).
Step 4: Tighten it clockwise to prevent water from leaking.
Step 5: Connect the hose and the Dohispa Universal motor, and place the motor inside the shampoo unit for secure positioning in water.
Step 6: Connect the switch wire to the motor wire.
Step 1: Detach the support base and hose.
Step 2: Wrap Teflon tape around it six times.
Step 3: Firmly insert the Aqua Bath filter to prevent it from rotating.
Step 4: Wrap Teflon tape around the upper part of the Aqua Bath filter six times.
Step 5: Check the white rubber ring under the support base and twist it into place.
Step 6: Open the Aqua Bath filter and insert the Dohispa carbon ball.
Step 7: Reassemble the filter.
Step 1: Loosen the inner motor filter to the left.
Step 2: Remove the inner mesh and clean it thoroughly with a brush or toothbrush.
Step 3: Inside, there's an inner urethane filter; twist it to remove and clean it with a brush or clean water. Reinsert it.
Step 4: Place the inner mesh filter (with the convex part facing downward) and twist the filter to the right to tighten it.
A) Yes, there is a controller that can adjust it into three different levels, depending on the customer's preference.
A) If you tighten the bolt all the way, the device will not be fixed properly. Please tighten the bolt until it is snug but not over-tightened.
1) Connect the power supply and the handle at the rear of the screen.
2) Wait for 5 seconds; it will automatically turn on.
3) Press the "Spectrum switch" button on the handle, and use the probe after the light is on.
1) Analyze the scalp surface skin:
- This includes the color, luster, and accumulation degree of the cuticle of the surface skin.
2) Analyze hair:
- This includes the number and health of the hair.
3) Analyze the hair follicle mouth environment on the scalp:
- Examine the oil and color of the hair follicle mouth.
Scalp: Pink with small red rashes, sometimes painful and itchy.
1) Sensitive Folliculitis: Due to the sensitivity of the scalp itself, external influences, dietary habits, and exposure to chemical irritants.
2) Seborrheic (지루성) Folliculitis: Caused by slow metabolism, excessive oil secretion, and the inability to produce normal secretions, resulting in small red rashes.
Hair: 1-2 pieces, uneven hair thickness.
- Hair follicle mouth: Hair fat blocks hair follicles, leading to severe hair loss.
A) Skin Surface Detection Mode (first light of spectral handle):
Detect dryness, oiliness, hair follicle blockage, skin wrinkles, aging, and freckles on the scalp skin.
B) Dermal Dermis Detection Mode (second light of spectral handle):
- Observe inflammation, capillary expansion, and blood exudation.
- Check whether the skin is normal, sensitive, or red after using skin care products.
C) Skin UV Layer Detection:
- Observe the blocking of skin pores and scalp hair follicles.
- If pores are blocked, fatty acids penetrate the skin through the pore, causing a skin stress reaction that produces a brick-red fluorescence reaction under UV light.
- 4-grid comparison mode.
- Screenshot.
- Video recording mode.
